rvc 32 product type style k 475 f tp 1. higher limiting element voltage compared with rmc (general use) 2. stability class : 5%
rated resistance is marked with 3-digit (e24) or 4-digit (e96) on the over coating. rvc16 : only 3digit marking is available.
example tolerance on rated resistance f 1% g 2% j 5% k 10% * packaging & standard qty. (min.) bulk (loose package) rvc50 rvc63 b paper tape tp rvc16 rvc20 rvc32 embossed tape te *refer to tape and packaging information on pages 46 and 47. all styles 1,000pcs. 5,000pcs. 4,000pcs. size code metric 16 1608 32 3216 50 5025 20 2012 63 6332 inch 0603 1206 2010 0805 2512 temperature coefficient of resistance k 100 10 -6 / c standard rated resistance 4-digit e96 series e.g. : 7154=7.15m ohm 3-digit e24 series e.g. : 475=4.7m ohm kamaya ohm 0.15 6.3 0.15 0.55 0.15 0.2 40mg 0.15 5.0 0.15 0.55 0.15 0.2 25mg 3.2 0.15 0.55 0.10 0.25 9mg 1.25 0.10 2.0 0.1 2012 3216 5025 6332 0.55 0.10 5mg 2mg w l metric 0805 1206 2010 2512 inch hcd 1.6 0.15 1.6 0.1 1608 0.45 0.10 0603 0.15 0.05 0.8 fixed thick film chip resistors; rectangular type & high voltage l cc w d d 2.5 3.2 0.5 0.2 0.4 0.1 0.3 0.6 0.6 0.2 0.2 0.25 0.5 0.2 0.4 0.1 0.3 0.6 0.6 h rvc unit : mm *values for reference *unit weight/pc. 8 chip resistors product specifications contained in this catalogue are subject to change at any time without notice. please confirm specificati ons with your order.
fixed thick film chip resistors; rectangular type & high voltage rvc note1. rated voltage = (rated dissipation) (rated resistance). (d.c. or a.c. r.m.s. voltage) note2. limiting element voltage can only be applied to resistors when the resistance value is equal to or higher than the cri tical resistance value. note3. critical resistance value is the resistance value at which the rated voltage is equal to the limiting element voltage.
description requirements no breakdown or flashover r 1g ohm r (1% 0.05 ohm) no visible damage, legible marking r (5% 0.1 ohm) no visible damage r (5% 0.1 ohm) no visible damage see ratings table in accordance with clause 4.17.4.5 r (1% 0.05 ohm) r (1% 0.05 ohm) no visible damage r (5% 0.1 ohm) no visible damage, legible marking r (5% 0.1 ohm) no visible damage no visible damage r (1% 0.05 ohm) test methods clause 4.7 clause 4.13 clause 4.23 clause 4.25.1 clause 4.8 clause 4.17 clause 4.18 clause 4.19 clause 4.24 clause 4.25.3 clause 4.32 clause 4.33 rvc16 100va.c.,60s rvc20~rvc63 500va.c.,60s the applied voltage shall be 2.5 times of the rated voltage or twice of the limiting element voltage, whichever is the less severe, 2s. dry/damp heat(12 12h cycle), first cycle./ cold/damp heat(12 12h cycle), remaining cycle. /d.c.load. rated voltage, 1.5h"on", 0.5h"off", 70 c, 1,000h. measuring temperature : 20 c/?5 c/ 20 c/ 125 c/ 20 c 235 c, 2s after immersion into the flux, the immersion into solder shall be carried out in solder bath at 260 c for 5s. 5 cycles between 55 c and 125 c. 40 c, 95%r.h., 56 days, test a) and b) of clause 4.24.2.1 125 c, no-load, 1,000h. 5n, 10s rvc16~rvc32 amount of bend : 3 mm rvc50, 63 amount of bend : 1 mm bend strength of the face plating voltage proof overload climatic sequence endurance at 70 c variation of resistance with temperature solderability resistance to soldering heat rapid change of temperature damp test, steady state endurance at the upper category temperature adhesion
the derated values of dissipation for temperatures in excess of 70 c shall be indicated by the following curve. !
" 55/125/56 lower category temperature ?5 c upper category temperature +125 c duration of the damp heat, steady-state test 56 days kamaya ohm rvc16 rvc20 rvc32 rvc50 rvc63 0.1 0.125 0.25 0.5 1.0 100 0 55 0 125 70 200 100 100 10m 400 500 800 200 100 200 100 200 100 200 100 500 200 200 k k k k k 100 51m f( 1%) g( 2%) e96 e24 j( 5%) k( 10%) e24 100 500 55 125 100 10m 100 51m 470 20m 470 51m 560 20m 470 47 47 47 47 100 47 10m 464 97.6 97.6 464 549 97.6 560 51m 1608 (0603) 2012 (0805) 3216 (1206) 5025 (2010) 6332 (2512) style combinations of rated resistance range and tolerance on rated resistance f( 1%) , g( 2%) j( 5%) , k( 10%) rated dissipation at 70 c w limiting element voltage v temperature coefficient of resistance preferred number series for resistors isolation voltage v category temperature range c 10 -6 / c code percentage of the rated dissipation(%) area of recommended operation ambient temperature ( c) size (inch) metric 9 chip resistors product specifications contained in this catalogue are subject to change at any time without notice. please confirm specificati ons with your order.
|
